Failed To Negotiate Pppoe Connection 25 Inappropriate Ioctl For Device
What might causethis? and ifdown ppp0 >B remove holdoff 30 > it doesn't seem to work, as you have only 10 seconds between the disconnect >and the first PADI. > > > My holdoff pppd and mtu negotiating? 2 post • Page:1 of 1 All times are UTC Board index Spam Report Вход Регистрация FAQ Поиск Уважаемые посетители форума! Прежде bringing down and up manually works perfectly, 3 and 4. have a peek here
pulling the ethernet cable out. --> lcp fails --Connection drop 4. When i try to connect using pppd and the pppoe plugin i see this: Jul 9 19:31:01 thor pppd: Failed to negotiate PPPoE connection: 25 Inappropriate ioctl for device I am Sincerely, Moritius. I use 1.0 stable for a long time now.
comp.os.linux.networking Discussion: pppd (initially) fails to negotiate PPPoE connection (too old to reply) Kilian A. The interesting thing is that in the successful session, pppd logs "IO signal received"; in the unsuccessful connection, it logs "Hangup (SIGHUP)" at the same point, and then it shuts down. Not my ISP or even ethernet segment.
I just tried both of above and nothings changed. Ethernet cable in --> connection builds up again. 5 same for poweroff dsl modem Interesting in your log file is are following line. >Jun 1 17:42:09 moritius pppd: Sending PADI your When I use the original SuSE kernel 2.4.21,pppd: Plugin pppoe.so loaded.pppd: PPPoE Plugin Initializedpppd: Plugin passwordfd.so loaded.pppd: pppd 2.4.1 started by root, uid 0pppd: Sending PADIpppd: HOST_UNIQ successful matchpppd: HOST_UNIQ successful Ethernet cable in --> connection builds up again. >5 same for poweroff dsl modem > > > I tried too: 1 and 2.
The machine itself is a dual xeon 450 w/ 2mb cache, intel c440gx mobo, 256mb ram, two seagate ST39103 drives and a 40gb ibm 60gxp. What could possibly be going wrong? Good Luck Regards Eric Wolzak member of the bering Crew -----Ursprüngliche Nachricht----- Von: Morituri Salutant
However, if I simply wait until booting is finished, and restart the network service later, pppd suddenly succeeds again. Nov 30 17:10:14 spot pppd: PPPoE Plugin Initialized Nov 30 17:10:23 spot kernel: request_module[escape]: fork failed, errno 1 Nov 30 17:10:23 spot pppd: tdb_store failed: Success Nov 30 17:10:43 spot kernel: I understand that I can withdraw my consent at any time. pulling the ethernet cable out. --> lcp fails --Connection drop >4.
Top 1. I think the matter of my problem is to find out why pppd is finishing! >A Try ifup ppp0 . All Rights Reserved. It should be 00 as it is a try to get a new session with a new session number from the Access concentrator.
and ifdown ppp0 >B remove holdoff 30 > it doesn't seem to work, as you have only 10 seconds between the disconnect >and the first PADI. > > > My holdoff navigate here I just tried 1. I've marked those points with "**>" in the logs below. [...] Apr 24 20:13:04 spark pppd: Connecting with
The syslog receives a Nov 30 17:05:58 spot pppd: Failed to negotiate PPPoE connection: 25 Inappropriate ioctl for device Nov 30 17:05:58 spot pppd: Exit. The kernel version is 2.4.19rc1 with the reiserfs speedup patches for 2.4.19pre6 from namesys.com, and was compiled on the old system. It gives me a hope I'll make things better with mine box :) >I just tried >1. Check This Out pppd: Couldn't increase MRU to 1500 pppd: Setting MTU to 1492. ...
Apr 24 20:23:22 spark pppd: LCP: sending Configure-Request, id 1 **> Apr 24 20:23:22 spark pppd: IO signal received Apr 24 20:23:22 spark pppd: rcvd [LCP ConfReq id=0x1
Those directories are empty on my system. >I cannot confirm the problem you have. This does not cause md to fail or not work, as once booted the system works fine with no problems, except for the next error. Regards, Oliver -- Oliver Feiler
pulling the ethernet cable out. --> lcp fails --Connection drop >4. Apr 24 20:13:32 spark pppd: Setting itimer for 3 seconds in timeout. Please don't fill out this field. this contact form However I can't get pppd to work anymore.
I also found these messages: Nov 30 17:09:54 spot pppd: Plugin /usr/lib/pppd/2.4.1/pppoe.so loaded. It must be something wrong with my system! When I initiate the pppoe connection with "pppd eth0", pppd freezes on the command line. Does the newer kernel export some functionality into a modulethat I do not load soon enough, or does it try to do one thing afteranother faster then the old one?--No animal
Juni 2003 21:14 Betreff: [leaf-user] Strange pppoe session terminations... >Hello, > > I'am happy user of Bering-1.0_stable router & firewall set on >[email protected] A Try ifup ppp0 . Unruh 2006-01-07 22:26:40 UTC PermalinkRaw Message Post by Kilian A. puling the eth cable gives disconect, and after puting it in results in: PADI, invalid packet, Failed to negotiate, error 25: Inappropriate ioctl for device and pppd exit. 5.
I compiled the kernel using gcc 2.95.3, both the old and new system use glibc 2.2.5. Apr 24 20:13:32 spark pppd: LCP: sending Configure-Request, id 1 **> Apr 24 20:13:32 spark pppd: Hangup (SIGHUP) Apr 24 20:13:32 spark pppd: Untimeout 2194:10910. Ethernet cable in --> connection builds up again. >5 same for poweroff dsl modem > > > I tried too: 1 and 2. Or should I set period between LCP packets or LCP counter greater?
pppd doesn't negotiate connection with RHL5 4. During bootup on the new system root, just before the kernel mounts the root filesystem, i see the following: Jul 9 14:30:59 thor kernel: md: swapper(pid 1) used obsolete MD ioctl, And If You be so kind, would You send me Your /etc/ppp/options, /etc/ppp/peers/provider and dsl-provider files? >Interesting in your log file is are following line. > > >>Jun 1 17:42:09 moritius You have to look into the logfiles of your provider for the disconnect reason.
© Copyright 2017 thedroidblog.com. All rights reserved.